Ground Source Heat Pumps

Ground source heat pumps (GSHPs) use pipes which are buried in the garden to extract heat from the ground. This heat can then be used to heat radiators, underfloor or warm air heating systems and hot water in your home.

A ground source heat pump circulates a mixture of water and antifreeze around a loop of pipe, called a ground loop, which is buried in your garden. Heat from the ground is absorbed into the fluid and then passes through a heat exchanger into the heat pump. The ground stays at a fairly constant temperature under the surface, so the heat pump can be used throughout the year.

The length of the ground loop depends on the size of your home and the amount of heat you need. Longer loops can draw more heat from the ground, but need more space to be buried in. If space is limited, a vertical borehole can be drilled instead.

The benefits of ground source heat pumps

  • Could lower your fuel bills, especially if you replace conventional electric heating
  • Could provide you with income through the government’s Renewable Heat Incentive (RHI)
  • Could lower home carbon emissions, depending on which fuel you are replacing
  • No fuel deliveries needed
  • Can heat your home as well as your water
  • Minimal maintenance required
  • Unlike gas and oil boilers, heat pumps deliver heat at lower temperatures over much longer periods. During the winter they may need to be on constantly to heat your home efficiently. You will also notice that radiators won’t feel as hot to the touch as they might do when you are using a gas or oil boiler.
  • Air source heat pumps are usually easier to install than ground source as they don’t need any trenches or drilling, but they are often less efficient than ground source heat pumps. Water source heat pumps can be used to provide heating in homes near to rivers, streams and lakes.

Find case studies and examples of homeowners who have installed a ground source heat pump using our Green Homes Network.

How do ground source heat pumps work?

Heat from the ground is absorbed at low temperatures into a fluid inside a loop of pipe (a ground loop) buried underground. The fluid then passes through a compressor that raises it to a higher temperature, which can then heat water for the heating and hot water circuits of the house. The cooled ground-loop fluid passes back into the ground where it absorbs further energy from the ground in a continuous process as long as heating is required.

Normally the loop is laid flat or coiled in trenches about two metres deep, but if there is not enough space in your garden you can install a vertical loop down into the ground to a depth of up to 100 metres for a typical domestic home. Heat pumps have some impact on the environment as they need electricity to run, but the heat they extract from the ground, the air, or water is constantly being renewed naturally.

Is a ground source heat pump suitable for me?

To tell if an air source heat pump is right for you, there are a few key questions to consider:

Is your garden suitable for a ground loop? It doesn’t have to be particularly big, but the ground needs to be suitable for digging a trench or a borehole and accessible to digging machinery.

Is your home well insulated? Since ground source heat pumps work best when producing heat at a lower temperature than traditional boilers, it’s essential that your home is well insulated and draught-proofed for the heating system to be effective.

What fuel will you be replacing? The system will pay for itself much more quickly if it’s replacing an electricity or coal heating system. Heat pumps may not be the best option for homes using mains gas.

What type of heating system will you use? Ground source heat pumps can perform better with underfloor heating systems or warm air heating than with radiator-based systems because of the lower water temperatures required.

Is the system intended for a new development? Combining the installation with other building work can reduce the cost of installing the system.

Our downloadable guide provides helpful advice about how to get the most out of your heat pump. Our heat pump trials guide, ‘The Heat Is On’, also gives recommendations. You may also want to consider air source heat pumps, which extract heat from the outside air. Use our renewables selector tool to find an appropriate technology for you.

Costs, savings and financial support

Maintenance

Heat pump systems typically come with a warranty of two to three years. Workmanship warranties for heat pumps can last up to 10 years, for example through QANW (Quality Assured National Warranties).

Many manufacturers also offer optional extensions of warranty for a fee. You can expect them to operate for 20 years or more, but they do require regular scheduled maintenance. A yearly check by you and a more detailed check by a professional installer every three to five years should be sufficient.

The installer should leave written details of any maintenance checks you should undertake to ensure everything is working properly. Consult with your supplier for exact maintenance requirements before you commit to installing a heat pump.

The Ground Source Heat Pump Association says there is no need for safety checks for ground source heat pumps and routine maintenance requirements are very low. These may include pre-heating season checks of the water pump, external pipes and fittings and electronics.

Get in touch

Get in touch to get more information from our team of advisers.
ITTC2 105 Plymouth Science Park
Plymouth
PL6 8BX